CSE8482 Octopus Express CompuScope

In stock
SKU
CSE8482 Octopus Express CompuScope
S$10,350.00

CSE8482 Octopus Express CompuScope 8 CH, 25 MS/s, 16-Bit PCIe

  • 8 Digitizing Input Channels
  • 25 MS/s Max. Sampling Rate per Channel
  • 20 MHz Analog Input Bandwidth
  • 16-Bit Vertical A/D Resolution
  • 2 GS (4 GB) Memory, Option 8 GS (16 GB)
  • Sustained PCIe Data Streaming at 2.0 GB/s
  • Software slectable impedance 50 Ω /1M Ω
  • Software selctabl: Voltage Ranges
  • Software selectable AC/DC Coupling
  • Clock: In/Out, Intenal/External, Reference
  • Trigger In & Trigger Out
  • Synch up to 8 cards up to 64 Ch system
  • Full-Height Full-Length PCIe Gen 2.0 x8 Card
  • Timestaping data capability
  • Driver for Windows 10/8/7 and Linux
  • GaGeScope PC Oscilloscope Software
  • SDK for C/C#, LabVIEW and MATLAB

Octopus Express CompuScope 8 CH, 25 MS/s, 16-bit, 20 MHz BWD, PCIe Digitizer

Overview

CSE8482 Octopus Express CompuScope is a 8 CH, 25 MS/s, 16-Bit with 20 MHz analog bandwidth, PCI Express digitizer board.

The Gage Octopus CompuScope family provides up to 8 channels in a single slot PCI Express (PCIe) or PCI card with up to 125 MS/s sampling per channel, and up to 16 GS of on-board acquisition memory. The Octopus CompuScope is available in 16-bit (CS84XX), 14-bit (CS83XX) A/D resolution models.

Lower-priced Octopus 14-bit (CS83XX) models provide the exact same functionality as the 16-bit (CS84XX), with the sole exceptions of lower vertical resolution and corresponding lower Dynamic Performance parameters (SNR, THD, SINAD, ENOB, SFDR) but with higher sampling rates.

GaGe CompuScope boards come with GaGeScope PC Oscilloscope Software. Further more there are Software Development Kit (SDK) C/C#, LabVIEW and MATLAB, supported on Wnidows as well as Linux Operation System.

Comparision of Octopus series of CompuScope PCIe boards:

Model Number A/D Resolution Number of Ch Max. Sampling per/Ch Memory Size Order Part number Cost in S$
CSE8482 16-bit 8 25 MS/s 2 GS (4 GB) OCE-848-002 S$10350.00
CSE8382 14-bit 8 25 MS/s 2 GS (4 GB) OCE-838-002 S$8950.00
CSE8385 14-bit 8 65 MS/s 2 GS (4 GB) OCE-838-005 S$10700.00
CSE8387 14-bit 8 100 MS/s 2 GS (4 GB) OCE-838-007 S$11550.00
CSE8389 14-bit 8 125 MS/s 2 GS (4 GB) OCE-838-009 S$11895.00
More Information
Specifications
ANALOG INPUT CHANNELS
Number of ch 8
AD resolution 16 bit
Connectors SMB
Sampling Rate 25 MS/s
Impedance 50 Ω or 1M Ω (software selectable)
Coupling AC or DC (software selectable)
Analog Bandwidth DC to 20 MHz
AC coupled 10 Hz to 20 MHz
Voltage Ranges ±100 mV, ±200 mV, ±500 mV, ±1 V, ±2 V,
±5 V, ±10 V (software selectable; ±10 V only
available on 1M Ω)
Flatness 7 MHz (16-bit). Measured at 125 MS/s &
50 MS/s in the ±500 mV range with 50 Ω input
impedance and 95% of full scale amplitude.
DC Accuracy ±0.5%. Measured on ±500 mV, ±1 V, ±2 V input
ranges for both 50 Ω and 1M Ω input
impedance settings.
DC User Offset ±1 x Full Range
(above ±5 V is limited to ±2.5 V)
Absolute Max. ±15 V (50 Ω), ±75 V (1M Ω on all but two lowest
Input Input Ranges, where Max is ±25 V)
TRIGGERING
Engines 2 per Channel,
1 for External Trigger
Source Any Input Channel,
External Trigger or Software
Input Combination All Combinations of Sources Logically OR’ed
Slope Positive or Negative (software selectable)
Sensitivity ±2% of Full Scale Input Range of Trigger
Source. This implies that signal amplitude
must be at least 4% of full scale to cause a
trigger to occur. Smaller signals are rejected
as noise.
Accuracy Less than ±2% of Full Scale for Channel
Triggering
Post-Trigger Data 128 points minimum. Can be defined with
16 point resolution.
EXTERNAL TRIGGER
Connector SMB
Impedance 2k Ω
Coupling AC or DC
Bandwidth >100 MHz
Voltage Range ±1 V, ±5 V (software selectable)
TRIGGER OUT
Connector SMB
Impedance 50 Ω
Amplitude 0 – 2.5 V
CLOCK IN
Connector SMB
Signal Level Minimum 1 V RMS,
Maximum 2 V RMS
Impedance 50 Ω
Coupling AC
Duty Cycle 50% ±5%
External Clock Minimum 10 MHz to Maximum Sampling
Mode Rates Rate of 125 MHz
External Reference 10 MHz ±1000 ppm; the external
Clock Mode Rate reference time base is used to
synchronize the internal sampling clock.
CLOCK OUT
Connector SMB
Signal Level 0 – 2.5 V
Impedance 50 Ω Compatible
Duty Cycle 50% ±5%
Output Modes Maximum Sampling Clock Frequency or
10 MHz Reference Clock
Max. Frequency 125 MHz
Min. Frequency 10 MHz from External Clock,
1 kHz from Internal Clock
MULTIPLE RECORD
Pre-Trigger Data Up to 32 kS Total
Record Length 128 points minimum. Can be defined
with 16 point resolution.
TIME-STAMPING
Timing Resolution One Sample Clock Cycle
Counter Turnover >24 Hours Continuous
MULTI-CARD SYSTEMS
Master/Slave Mode Provides synchronized triggering and
sampling on all channels for all cards to
create larger multi-channel systems.
Independent Mode Each card operates independently within
the system.
Number of Cards 2 to 8 Cards for up to 64 Channels Total
DIMENSIONS
Size Single Slot, Full Height, Full Length
POWER CONSUMPTION
Power 25 Watts (typical)
PC SYSTEM REQUIREMENTS
PCI Express (PCIe) Slot 1 Free Full-Height Full-Length
PCIe Gen1, Gen2 or Gen3, x8 or x16 Slot
Operating System Windows 10/8/7 (32-bit/64-bit),
Linux – Requires SDK for C/C#
Write Your Own Review
You're reviewing:CSE8482 Octopus Express CompuScope
Your Rating
Slava Yurthev Copyright