DCA08G160 RF Receiver & Downconverter, 8 GHz
- RF range: 9 kHz to 8 GHz
- Three selectable BW output:
- 160 MHz @ Center IF 0 Hz
- 80 MHz @ Center IF 55 MHz
- 10 MHz @ Center IF 35 MHz
- 9 Ch Pre-Select Filter Bank no Pre-Amplifier
- Tuning Resolution : 10 Hz
- Frequency Reference: 10 MHz
- RF input : SMA female 50 Ω
- Ethernet : 10/100/1000 RJ45
- Digitizer Resolution Options: 16-bit up to 1 GS/s or 12-Bit up to 3 GS/s
- Real-Time Data Capture to Digitizer Memory:up to 8 GB or 16 GB
- Real-Time Data Capture to Data Storage System: up to 192 TB
- Real-Time No Programming Spectrum Analyzer App – SpectraScopeRT
- MATLAB Support for Control, Acquisition, and Signal Processing
- Sustained Gap-Free PCIe Streaming to Host System: up to 5 GB/s
- Multi-Channel Systems with 10 MHz In/Out Reference Synchronization
- Software Devlopment Kit:
CompuScope SDK for C/C#
CompuScope SDK for MATLAB
CompuScope SDK for LabVIEW
RF Receiver & Downconverter, 8 GHz
The DCA08G160 is a RF Riciever and Downconverter featuring breakthrough frequency and bandwidth coverage for the size and cost, covering frequency ranges from 9 kHz to 8 GHz.
The DCA08G160 downconverters has a bandwidths of 160 MHz direct conversion (centered at 0 Hz IF) I and Q analog outputs. These wideband version can be software configured for super-heterodyne mode with a bandwidth of either 80 MHz or 10 MHz on a single IF output centered at 55 MHz IF.
The DCA08G160 is engineered for analyzing wideband digital communications - cell phone standards 3G/4G/LTE, WiFi, or general Vector Signal Analysis (VSA) applications involving broadband signals.
The DCA08G160 RF front end is a unique architecture, consisting of both super-heterodyne and direct conversion technologies that are software selectable. The front-end processing blocks utilize 9 preselect filters to mitigate input-related spurs and image responses.
The DCA08G160 model combined with GaGe high-speed digitizers allow for complete real-time signal recording and analysis systems covering frequencies up to 8 GHz RF Signal spectrum. These solutions greatly extend the digitizer's frequency range allowing those developing applications in R&D, Manufacturing Test, and Field Service a high performance lower cost platform for complex wideband RF and microwave signal analysis.
The DCA08G160 bandwidth modes of 100 MHz, 40 MHz, and 10 MHz ideally suited for use with GaGe 16-bit resolution Razor Express 16XX PCIe Digitizer at up to 200 MS/s or RazorMax at up to 500 MS/s or 1 GS/s for real-time gap free signal recording at 100 MHz bandwidth.
10 MHz reference inputs and outputs on both the GaGe digitizers and downconverter units provide a single frequency reference for synchronized operation for multiple systems.
The large onboard FIFO memory of the GaGe digitizers allow for real-time streaming of I and Q baseband signals at up to 1.6 GB/s (Razor Express) or 5 GB/s (RazorMax Express or EON Express) over PCI Express to PC memory for post processing, display, and storage.
The digitizers and downconverters have full control and data acquisition support via Mathworks MATLAB, with example programs furnished to facilitate rapid signal processing and modulation analysis program development. Additional software SDK and example programs are available for C/C# and LabVIEW.
For manual control, testing and setup of the Ethernet connected downconverters, programs are provided for network discovery, setting carrier frequency, RF / IF gain, filters, etc.
SpectraScopeRT is a Windows based spectrum analyzer application software that requires no programming and allows for integrated operational control of both the downconverter receiver and the digitizer for signal capture, analysis, and recordings. SpectraViewRT is used to conduct playback of previous signal recordings to the display monitor for analysis.</div