CSE1442 Razor Express

In stock
CSE1442 Razor Express

CSE1442 Razor Express CompuScope, 4 Ch, 200 MS/s, 14 bit, PCIe


  • 4 Ch, 14 bit A/D, Simultaneous input
  • 200 MS/s Maximum Sampling Rate per Channel
  • 125 MHz Analog Input Bandwidth
  • Software Selectable Sampling Rates, 1 kS/s to 200 MS/s
  • 4 GS (8 GB) memory buffer, Expandable up to 8 GS (16 GB)
  • Sustained PCIe Data Streaming at 1.6 GB/s
  • Full-Featured Front-End, AC/DC Coupling, 50 Ω /1M Ω Inputs
  • External or Reference Clock In/Clock Out
  • Multi-Card Synchronization up to 8 Cards (32 Ch )
  • Full-Height Full-Length PCI Express Gen 2.0 x8 Card
  • GaGeScope PC Oscilloscope Software
  • SDK C/C#, LabVIEW and MATLAB
  • Windows, Linux OS Supported
  • RADAR Design and Test
  • Signals Intelligence (SIGINT)
  • Ultrasonic Non-Destructive Testing
  • LIDAR Systems
  • Communications
  • Spectroscopy
  • High-Performance Imaging
  • Time of Flight
  • Particle Physics

CSE1442 Razor Express CompuScope, 4 Ch, 200 MS/s, 14 bit, PCIe

The GaGe Razor Express16XX CompuScope PCIe digitizer board features 14-bit resolution with sampling rates up to 200 MS/s with true Effective Number of Bits (ENOB) of 11.7-bits with 5 MHz input.

Onboard digitizer sample memory is expandable up to 8 GS (16 GB) and up to 8 Razor Express digitizers can be combined for up to 32 channels in a single system.

The Razor Express can be combined with wideband downconverter models and PC solutions to be the heart of a wideband, multi-channel, RF/Microwave signal analysis and recording system covering frequencies up to 27 GHz and up to 50 MHz bandwidth.

More Information
Number of Ch 4
A/D Resolution 14 bit
Sampling Rate 200 MS/s
Connectors SMA
Impedance 50 Ω or 1M Ω (software selectable)
Coupling AC or DC (software selectable)
Analog Bandwidth DC (50 Ω) = DC to 125 MHz
  AC (1M Ω) = 10 Hz to 65 MHz
Voltage Ranges ±100 mV, ±200 mV, ±500 mV, ±1 V, ±2 V,
  ±5 V, ±10 V, ±20 V, ±50 V (software
  selectable; ±10 V, ±20 V, ±50 V only
  available on 1M Ω)
Flatness Within ±0.5 dB of ideal response to 100
  MHz. Measured at 100 MS/s in the ±500 mV
  range with 50 Ω input impedance and 95%
  of full scale amplitude.
DC Accuracy ±0.5%. Measured on ±500 mV, ±1 V, ±2 V
  input ranges for both 50 Ω and 1M Ω input
  impedance settings.
DC User Offset ±1 x Full Range
  (above ±5 V is limited to ±2.5 V)
Absolute Max. Input ±15 V (50 Ω), ±75 V (1M Ω on all but two
  lowest Input Ranges, where Max is ±25 V)
Type 3-pole, 1 per Channel
Cut-Off Frequency 25 MHz
Operation Individually Software Selectable
Engines 2 per Channel,
  1 for External Trigger
Source Any Input Channel,
  External Trigger or Software
Input Combination All Combinations of Sources Logically OR’ed
Slope Positive or Negative (software selectable)
Sensitivity ±2% of Full Scale Input Range of Trigger
  Source. This implies that signal amplitude
  must be at least 4% of full scale to cause a
  trigger to occur. Smaller signals are rejected
  as noise.
Accuracy Less than ±2% of Full Scale for Channel
Post-Trigger Data 32 points minimum. Can be defined with 32
  point resolution.
Connector SMA
Impedance 2k Ω
Coupling AC or DC
Bandwidth >100 MHz
Voltage Range ±1 V, ±5 V (software selectable)
Connector SMA
Impedance 50 Ω
Amplitude 0 – 1.8 V
Connector SMA
Signal Level Minimum 1 V RMS,
  Maximum 2 V RMS
Impedance 50 Ω
Coupling AC
Duty Cycle 50% ±5%
Input Modes External Clock or
  10 MHz Reference Clock
External Clock Minimum 10 MHz to Maximum Sampling
Mode Rates Rate of 200 MHz.
External Reference 10 MHz ±1000 ppm; the external
Clock Mode Rate reference time base is used to
  synchronize the internal sampling clock.
Connector SMA
Signal Level 0 – 1.8 V
Impedance 50 Ω Compatible
Duty Cycle 50% ±10%
Output Modes Maximum Sampling Clock Frequency or
  10 MHz Reference Clock
Max. Frequency 200 MHz
Min. Frequency 10 MHz from External Clock,
  1 kHz from Internal Clock
Pre-Trigger Data Up to 32 kS Total
Record Length 32 points minimum. Can be defined with
  32 point resolution.
Timing Resolution One Sample Clock Cycle
Counter Turnover >48 Hours Continuous
Master/Slave Mode Provides synchronized triggering and
  sampling on all channels for all cards to
  create larger multi-channel systems.
Independent Mode Each card operates independently within
  the system.
Number of Cards 2 to 8 Cards for up to 32 Channels Total
Size Single Slot, Full Height, Full Length
Power 25 Watts (typical)
PCI Express (PCIe) Slot 1 Free Full-Height Full-Length
  PCIe Gen1, Gen2 or Gen3, x8 or x16 Slot
Operating System Windows 10/8/7 (32-bit/64-bit),
  Linux – Requires SDK for C/C#
Software Support
Software Development Kit
SDK C/C# Windows and Linux
  SDK MATLAB Windows
  Linux – Requires SDK for C/C#
Application Software GageScope Lite
  GageScope Standard
  GageScope Pro
Write Your Own Review
You're reviewing:CSE1442 Razor Express
Your Rating