DCA27G100

In stock
SKU
DCA27G100
S$26,080.00

DCA27G100 RF Receiver & Downconverter, 27 GHz

Features

  • RF range: 9 kHz to 27 GHz
  • Three selectable BW output:
    • 100 MHz @ Center IF 0 Hz
    • 40 MHz @ Center IF 35 MHz
    • 10 MHz @ Center IF 35 MHz
  • 21 Ch Pre-Select Filter Bank no Pre-Amplifier
  • Tuning Resolution : 10 Hz
  • Frequency Reference: 10 MHz
  • RF input : SMA female 50 Ω
  • Ethernet : 10/100/1000 RJ45
  • Digitizer Resolution Options: 16-bit up to 1 GS/s or 12-Bit up to 3 GS/s
  • Real-Time Data Capture to Digitizer Memory:up to 8 GB or 16 GB
  • Real-Time Data Capture to Data Storage System: up to 192 TB
  • Real-Time No Programming Spectrum Analyzer App – SpectraScopeRT
  • MATLAB Support for Control, Acquisition, and Signal Processing
  • Sustained Gap-Free PCIe Streaming to Host System: up to 5 GB/s
  • Multi-Channel Systems with 10 MHz In/Out Reference Synchronization
  • Software Devlopment Kit:
    CompuScope SDK for C/C#
    CompuScope SDK for MATLAB
    CompuScope SDK for LabVIEW

DCA27G100 RF Receiver & Downconverter, 27 GHz

The DCA27G100 is a RF Riciever and Downconverter featuring breakthrough frequency and bandwidth coverage for the size and cost, covering frequency ranges from 9 kHz to 27 GHz.

The DCA27G100 downconverters has a bandwidths of 100 MHz direct conversion (centered at 0 Hz IF) I and Q analog outputs. These wideband version can be software configured for super-heterodyne mode with a bandwidth of either 40 MHz or 10 MHz on a single IF output centered at 35 MHz IF.

The DCA27G100 is engineered for analyzing wideband digital communications - cell phone standards 3G/4G/LTE, WiFi, or general Vector Signal Analysis (VSA) applications involving broadband signals.

The DCA27G100 RF front end is a unique architecture, consisting of both super-heterodyne and direct conversion technologies that are software selectable. The front-end processing blocks utilize 9 preselect filters to mitigate input-related spurs and image responses.

The DCA27G100 model combined with GaGe high-speed digitizers allow for complete real-time signal recording and analysis systems covering frequencies up to 8 GHz RF Signal spectrum. These solutions greatly extend the digitizer's frequency range allowing those developing applications in R&D, Manufacturing Test, and Field Service a high performance lower cost platform for complex wideband RF and microwave signal analysis.

The DCA27G100 bandwidth modes of 100 MHz, 40 MHz, and 10 MHz ideally suited for use with GaGe 16-bit resolution Razor Express 16XX PCIe Digitizer at up to 200 MS/s or RazorMax at up to 500 MS/s or 1 GS/s for real-time gap free signal recording at 100 MHz bandwidth.

10 MHz reference inputs and outputs on both the GaGe digitizers and downconverter units provide a single frequency reference for synchronized operation for multiple systems.

The large onboard FIFO memory of the GaGe digitizers allow for real-time streaming of I and Q baseband signals at up to 1.6 GB/s (Razor Express) or 5 GB/s (RazorMax Express or EON Express) over PCI Express to PC memory for post processing, display, and storage.

The digitizers and downconverters have full control and data acquisition support via Mathworks MATLAB, with example programs furnished to facilitate rapid signal processing and modulation analysis program development. Additional software SDK and example programs are available for C/C# and LabVIEW.

For manual control, testing and setup of the Ethernet connected downconverters, programs are provided for network discovery, setting carrier frequency, RF / IF gain, filters, etc.

SpectraScopeRT is a Windows based spectrum analyzer application software that requires no programming and allows for integrated operational control of both the downconverter receiver and the digitizer for signal capture, analysis, and recordings. SpectraViewRT is used to conduct playback of previous signal recordings to the display monitor for analysis.

</div
More Information
Specifications
Tuning and Bandwidth
Frequency Range 9 kHz to 27 GHz
Tuning Resolution IF ouput 10 Hz
Bandwidth (software selectable) 10 MHz, 40 MHz, 100 MHz
Spurious Free Dynamic Range (SFDR)
@ 100 MHz Bandwidth 60 dBc (typical)
@ 10 / 40 MHz Bandwidth 70 dBc (typical)
Frequency Reference
Internal/External 10 MHz
Internal 10 MHz Oscillator Stability ±1 ppm
Amplitude
Accuracy from 50 MHz to 27 GHz,at 25 °C ± 5 °C ± 2.00 dB typical
Measurement Range DANL to max. safe input level
Attenuator Range – 27 GHz Model 0 to 30 dB in 10 dB steps (IF attenuation)
Max. Safe RF Input Level +10 dBm, 0 V DC
Third Order Intercept (TOI)
At 1 GHz +12 dBm, typical
Pre-Selection Filter Bank
27 GHz Model – DCA27G 18-channel switched
Panel Connectors
RF Input SMA female, 50 Ω
10 MHz Reference In & Out SMA female, 50 Ω
Analog I and Q Out SMA female, 50 Ω
10/100/1000 Ethernet RJ-45
USB 2.0 Console Type B Mini
GPIO 25-pin Male D-Subminiature
Coaxial Power Type A 5.5 mm OD, 2.5 mm ID
Physical
Power Supply Input AC 120V-240V / Output +12V
Power Consumption 19 W (8 GHz)
Operating Temperature Range 0°C to +50°C / 32° to 122° F
Storage Temperature Range -40°C to +85°C / -40° to 185° F
Enclosure Dimensions 269 (L) x 173 (W) x 61 (H) mm
10.58 (L) x 6.81 (W) x 2.40 (H) inches
Weight 2.7 kg / 6 lbs.
Regulatory Compliance
RoHS Compliance RoHS
Marks CE, European Union
EMC Directive 2014/30/EU EN 61326-1 2013
Electromagnetic Compatibility
Low Voltage Directive 2006/95/EC FCC EN 61010-1 2010 Class 1 Safety
Write Your Own Review
You're reviewing:DCA27G100
Your Rating
Slava Yurthev Copyright